相信大家都知道，作為動力傳動設備——皮帶，作為備件之一，燃氣發電機組的使用幾乎離不開這部分，它負責驅動機組風機的轉動，同時也帶動機組的風扇轉動。充電器，使其在發電機組中。在運行期間為電池充電。功能這么多，它的使用壽命當然也在一定的時間范圍內。那么，當達到這種情況時，我們需要更換它嗎？

As we all know, as a power transmission equipment - belt, as one of the spare parts, the use of gas-fired generator set is almost inseparable from this part, which is responsible for driving the rotation of the fan of the unit and driving the rotation of the fan of the unit at the same time. Charger in the generator set. Charge the battery during operation. With so many functions, its service life is certainly within a certain time range. Then, when this situation is reached, do we need to replace it?

當發電機出現一些幾個問題，發電機的皮帶應該進行更換！

When the generator has some problems, the belt of the generator should be replaced!

1.發電機在工作時，發電機的三角度會保持一定的緊張程度，正常情況下三角帶的壓力會有所增加。

1. When the generator is working, the triangle of the generator will maintain a certain degree of tension, and the pressure of the triangle belt will increase under normal circumstances.

2.當三角帶能按下10-20mm的距離的時候，過緊容易導致發電機、風扇和水泵的軸承磨損加劇一起故障。

2. When the V-belt can be pressed for a distance of 10-20mm, it is easy to cause the bearing wear of generator, fan and water pump to intensify and cause a fault.

3.三角度過送會導致驅動的附件達不到需要的轉速，容易導致皮帶出現出槽，發電機電壓、風扇風量、水泵量降低，影響發電機的正常運作。

3. Over feeding of the triangle will cause the drive accessories to fail to reach the required speed, which is easy to cause the belt to slot, and the generator voltage, fan air volume and water pump volume will be reduced, affecting the normal operation of the generator.

4.一般皮帶基層出現裂紋時（即皮帶出現裂紋，芯部斷裂，槽段開裂）；帶基層與槽段分離；底座磨損和破裂；松線、側材損傷、側硬化、側滑、上表面裂紋）；帶槽段內徑與帶輪槽底之間無間隙。當這些情況發生時，我們需要更換皮帶。

4. When cracks appear in the base course of the general belt (that is, cracks appear in the belt, the core is broken, and the groove section is cracked); The belt base is separated from the groove section; The base is worn and broken; Loose wire, side material damage, side hardening, side sliding, upper surface crack); There is no gap between the inner diameter of the groove section and the bottom of the pulley groove. When these conditions occur, we need to replace the belt.

如果不及時更換，會導致機組風扇轉速過慢，導致機組散熱不足導致水溫偏高。當機組的某些部件出現肉眼可見的故障時，我們需要更換部件。如果不及時更換，將導致機組發生一次或多次故障。這些看似不起眼的小故障可能會導致關機。

If it is not replaced in time, the fan speed of the unit will be too slow, resulting in insufficient heat dissipation of the unit and high water temperature. When some parts of the unit have visible faults, we need to replace them. If it is not replaced in time, it will cause one or more failures of the unit. These seemingly insignificant small faults may lead to shutdown.

所以說燃氣發電機使用一段時間要進行維護，對發電機皮帶進行檢查，如發現芯部斷裂以及槽斷面開裂的缺陷時，這時，我們就要立即更換。更多相關內容就來關注我們網站http://biandang123.cn進行咨詢了解吧！

Therefore, the gas generator should be maintained for a period of time, and the generator belt should be checked. If the core is broken and the groove section is cracked, we should replace it immediately. Follow our website for more relevant content http://biandang123.cn Consult and understand!