瓦斯發電機組的選購以及使用之前的注意是怎樣的呢？只有多多去了解相關的事項，才能更好更順利更安全的操作機器，下面小編為您講解一番吧。

What is the attention before choosing and using gas generator set? Only by learning more about relevant matters can we operate the machine better, more smoothly and more safely. The following editor will explain it to you.

瓦斯發電機組的選購注意

Notes on the purchase of gas generator set

1、瓦斯發電機組的界限尺寸、安裝尺寸及連接尺寸均符合規定程序批準的廠品圖樣

1. The boundary dimension, installation dimension and connection dimension of the gas generator set shall comply with the factory product drawing approved by the specified procedure

2、機組的焊接應牢固，焊縫應均勻，無焊穿、咬邊、夾渣及氣孔等缺陷，焊渣焊藥應清除干凈；漆膜應均勻，無明顯裂縫和脫落；鍍層應光滑，無漏鍍斑點、銹蝕等現象；機組緊固件應不松動。

2. The welding of the unit shall be firm, the welds shall be uniform, and there shall be no defects such as welding penetration, undercut, slag inclusion and pores, and the welding slag and flux shall be removed; The paint film shall be uniform without obvious cracks and falling off; The coating shall be smooth and free of missing spots, rust and other phenomena; The fasteners of the unit shall not be loose.

3、瓦斯發電機的電氣安裝應符合電路圖，機組的各導線連接處應有不易脫落的明顯標志。

3. The electrical installation of the gas generator shall comply with the circuit diagram, and the wire connections of the unit shall have obvious marks that are not easy to fall off.

4、瓦斯發電機應有接地良好的端子。

4. The gas generator shall have terminals with good grounding.

瓦斯發電機組使用之前的注意

Precautions before using gas generator set

瓦斯發電機組在啟動前，先打開氣源供氣閥門，檢查管路的連接是否可靠.如果管路中安裝穩壓罐，還應打開其底部的排污閥，放掉穩壓罐中的污物，排凈空氣，關閉排污閥.向油底內加注機油至規定油面位置，向冷卻系統的內加注冷卻液，檢查電動系統的電路連接是否正確，蓄電池電量是否充足.檢查氣路.

Before starting the gas generator set, open the gas supply valve to check whether the connection of the pipeline is reliable If a surge tank is installed in the pipeline, the blowdown valve at the bottom of the tank should also be opened, the dirt in the surge tank should be discharged, the air should be discharged, and the blowdown valve should be closed Fill the oil in the oil pan to the specified oil level, fill the coolant in the cooling system, check whether the circuit connection of the electric system is correct and whether the battery power is sufficient. Check the air circuit

檢查燃氣管路上的壓力表指示是否正常，打開瓦斯發電機組的進氣閥門，接通電源開關.使調速器怠速額定開關處于怠速狀態起動發動機.待油溫，水溫分別升至45度，70度，油壓高于0.245MPA，將瓦斯發電機組的升至高速工作.

Check whether the indication of the pressure gauge on the gas pipeline is normal, open the air inlet valve of the gas generator set, turn on the power switch, make the governor idle speed rated switch in the idle state, and start the engine. Wait until the oil temperature, the water temperature rises to 45 degrees and 70 degrees respectively, and the oil pressure is higher than 0.245Mpa, and then raise the Wasi generator set to high-speed operation

對新機或停放5天以上未使用的瓦斯發電機組，起前應盤動曲軸3-5轉.對于平時停放作為應急用的瓦斯發電機組，為便于在急用時能迅速起動運行，停放期內，每隔3-5天試運行一次至水，油溫度到60度以上.

For the new machine or the gas generator set that has not been used for more than 5 days, turn the crankshaft for 3-5 revolutions before starting For the gas generator set that is normally parked for emergency use, in order to quickly start and operate in case of emergency, the test run shall be conducted every 3-5 days during the parking period until the water and oil temperature reach more than 60 ℃

此外如果遇到發電機組出現了故障，操作人員不要慌，應鎮靜下來，仔細實時地根據故障發生的特征，判斷其產生的原因在哪里。更多事項了解就來我們網站http://biandang123.cn咨詢吧。

In addition, if there is a fault in the generator set, the operator should not panic, should calm down and carefully determine the cause of the fault in real time according to the characteristics of the fault. Come to our website for more information http://biandang123.cn Consult.