如果燃氣發電機組氣缸套的溫度過高或過低，控制模塊會發出氣缸套水溫高或水溫低的警報，原因是什么呢？

If the temperature of the cylinder liner of the gas generator set is too high or too low, the control module will give an alarm of high or low water temperature of the cylinder liner. What is the reason?

缸套水溫高的原因為：

The reasons for the high water temperature of the cylinder liner are:

漏水或損耗過大而導致缸套水不足;散熱水箱積塵較多，或風扇出現故障無法散熱;節溫器出現故障;缸套的水溫度傳感器或電路出現故障;超過負荷范圍;具體診斷方法為：對散熱水箱電機的運行狀況進行檢查，及時更換故障電機如發現水箱散熱片出現堵塞及時進行水箱的清理;及時更換故障節溫器;對缸套水溫度傳感器進行故障檢測，并對電路回路予以判斷，及時進行更換與維修處理;降低負荷。

Insufficient cylinder liner water due to water leakage or excessive loss; There is too much dust in the cooling water tank, or the fan fails to dissipate heat; Failure of thermostat; Water temperature sensor or circuit of cylinder liner is faulty; Exceeding the load range; The specific diagnosis methods are as follows: check the operation condition of the motor of the cooling water tank, replace the faulty motor in time, and clean the water tank in time if the radiator of the water tank is found to be blocked; Timely replace the faulty thermostat; Detect the fault of cylinder liner water temperature sensor, judge the circuit circuit, and replace and repair it in time; Reduce the load.

缸套水溫度較低的原因：

Reasons for lower cylinder liner water temperature:

加熱器出現故障;缸套水溫度傳感器或電路發生故障;節溫器未正常開啟;具體診斷方法為：檢測加熱器溫控開關是否正常開啟，并對停機繼電器的運行進行檢查，及時進行配件更換;排查傳感器及電器回路;檢查節溫器是否存在故障。

Heater failure; Cylinder liner water temperature sensor or circuit fault; The thermostat is not normally opened; The specific diagnosis methods are as follows: check whether the temperature control switch of the heater is normally opened, check the operation of the shutdown relay, and replace the parts in time; Check the sensor and electrical circuit; Check whether the thermostat is faulty.

故障診斷的步驟：

Steps for fault diagnosis:

通過機組的配套ET對有關參數進行檢查，對于發生故障發生機組所有異?，F(xiàn)象掌握清楚，并進行以下問題的分析與查證：

Check the relevant parameters through the matching et of the unit, master all abnormal phenomena of the unit in case of failure, and analyze and verify the following problems:

查閱檢修記錄，燃氣發電機組經過哪些相關的維修或保養;是否曾經發生過相似的故障，是怎樣解決的;機組的運行環境是否有變化

Check the maintenance records and find out the relevant maintenance or repair of the gas generator unit; Whether similar faults have occurred and how to solve them; Is there any change in the operating environment of the unit

在對機組故障進行診斷的基礎上，對造成故障的原因進行具體分析以確定故障發生具體部位。

On the basis of unit fault diagnosis, the cause of the fault is analyzed to determine the specific location of the fault.

在故障定位以后，對相關的部位和部件進行檢查，以確定故障發生的具體原因并采取排除措施。

After the fault is located, relevant parts and components shall be inspected to determine the specific cause of the fault and take troubleshooting measures.

發電機組氣缸套水溫過高或過低的原因以及相關的診斷方法就到這里了，您可以作為參考使用，更多相關信息就來我們網站http://biandang123.cn獲取吧。

This is the reason why the water temperature of the cylinder liner of the generator set is too high or too low and the relevant diagnosis method. You can use it as a reference. For more relevant information, please visit our website http://biandang123.cn Get it.